English
WELCOME TO MBY
You are here: Home / Main Products / Water Pump Bearings / Water pump bearings WA WB Series(Ball/Ball) 3

PRODUCTS

PRODUCTS

Water pump bearings 
 
Water pump bearings are double row bearings and, in contrast to conventional double row bearings, do not have an inner ring but raceways machined directly into the surface of the shaft. As a result, there is more space available for the rolling elements, giving a higher specific load carrying capacity than that of solutions with conventional single bearings. Furthermore, it is possible in this type of bearing to achieve economical combinations of ball and roller rows. In a small design envelope, this gives a broad range of load carrying capacities.
The use of a common outer ring for two rows of rolling elements prevents misalignment defects, eliminating the risk of undesirable distortion of the bearings.
In water pump bearings, the ends of the shaft normally extend beyond the outer ring on both sides. The length and diameter of these extended sections are matched to the specific application. This results in
a simple, ready-to-fit bearing unit that is primarily used in water pumps for road vehicles.
However, they are not restricted to this application.
Due to the advantages described above, they have a wide range of possible applications.
They can be used, for example, in:
■ fans
■ tension pulleys
■ vane pumps
■ angle grinders.
Since they are not restricted to use in water pumps, water pump bearings are also described in English as Integral shaft bearings.

Designation system

A new designation system has been developed for water pump bearings,  The design of the bearing can be deduced from the designation.
 
1.The letter W stands for “Water pump bearing”.
2.The second letter indicates the design: 
  A: Ball/ball, asymmetrical design
  B: Ball/ball, symmetrical design R: Roller/ball
  T: Roller/ball, three point contact F: Roller/ball, four point contact
3.This figure indicates the number of shaft shoulders:
  0: Smooth shaft
  1: One end of the shaft has a shoulder 
  2: Both ends of the shaft have shoulders
4.Four digit serial number
5.Variant (e.g. different seal material)
QQ截图20190719094451


Design: Ball/Ball   WA,WB Series
QQ截图20190719100617

Dimension table (continued) · Dimensions in mm
Outer ring diameter Designation Mounting dimensions Previous designation
D









L L1 L2 C dk D11 D22 L11 L22
40 WB11091.11) 135,7 18,8 56,9 60 24,5 15,002 53,2
WB21110 140,9 24 56,9 60 24,5 20,002 15,002 23 53,2
WB11000 147 35,5 51,5 60 20,002 15 47,8
WB211141) 177,6 23,4 92,2 62 20,004 15,944 15,002 6 80,7
WB21129 177,6 23,4 92,2 62 20,004 15,944 15,002 6 80,7
47 WB116011) 43,6 23 20,6 28,4 24,5
WB116021) 60,6 23 37,6 28,4 24,5
WB051151)5) 76 20 8 48 26 F-226707.3
WB21320 93 16 42 35 24 15,918 12,038 15 40
WB111281) 111,2 1 62,2 48 26 15 41
WB211271) 135,2 25 48,2 62 26 15,944 15,002 8 41
WB111131) 137,5 1 61,5 75 26 15 44
WB111461) 139,2 3,8 64,9 70,5 26 15,002 43,7
WB211151) 154,2 18,8 64,9 70,5 26 24,5 15,002 18,8 43,7
WB21521 156,7 26 62,7 68 20,004 15,944 15,002 6,5 20
52 WB21388.081)4) 113,25 22,25 44 47 25 12x1,25 12,038 10 42
55 WA11665 130 32 50,65 47,35 30 15,01 47,8 WS2511.H93

1)  Special shaft
2) Flinger sleeve
3) R-SAFE seal
4) Rotary shaft seal
5) No seal